Loading 3D Sensor...

Catch Motor Faults Weeks Before Failure

Track bearing wear, shaft misalignment, and rotor imbalance on every motor and pump—without pulling power or data cables.

Spot Bearing Wear & Imbalance Early
The sensor wakes on schedule to sample all 3 axes (X, Y, Z) at 8 kHz. It removes DC offset, integrates acceleration to velocity with a 5 Hz high-pass filter, and records RMS velocity, peak velocity, and 4,096-sample waveforms so you can diagnose faults before a bearing seizes.
Instant Green, Amber & Red Health Status on the Machine
Every measurement is checked on the sensor against ISO 10816-3 machine limits, custom thresholds, and temperature bounds. Bright Green, Amber, and Red LEDs show machine health right on the motor casing.
Built to Survive Washdowns, Heat & Heavy Vibration
A machined aluminium base and ABS cap house electronics sealed in solid epoxy potting. The rigid potting blocks moisture and chemical ingress while transferring motor vibration directly to the sensor without internal board resonance.
Install on Any Motor or Pump in Minutes
Bolt the sensor directly to a motor, pump, or gearbox housing with a center M5 socket head cap screw, or bond its flat machined base with industrial adhesive—no conduit, junction boxes, or plant shutdown required.
Years of Autonomous Operation (-40°C to +85°C)
A Lithium Thionyl Chloride (Li-SOCl₂) battery powers the sensor for years of scheduled logging across freezing outdoor pads and hot motor casings (-40°C to +85°C).
32 MB On-Board History & Wireless Bluetooth LE Readout
Up to 32 MB of non-volatile flash memory stores long-term velocity trends and raw diagnostic waveforms on the motor. Read out machine history wirelessly over Bluetooth Low Energy 5.2 with a phone, tablet, or fixed gateway.
ACTUAL DEVICE FIRMWARE RUNNING IN BROWSER

Try our sensor here

1.0× g
Status LEDs
Ready
Sampling...
Selected Measurement Statistics No record selected
Z RMS Velocity
— mm/s
X / Y RMS Velocity
— / — mm/s
Z Peak Velocity
— mm/s
ISO 10816-3 Zone
—
Temperature
— °C
Battery / Log Time
—

Saved Measurements

Click any record to pause & inspect

0

1. Statistical RMS Velocity Trend

Tracks broadband RMS velocity (mm/s) over time against ISO 10816-3 Alarm (4.2 mm/s) and Trip (9.5 mm/s) limits

Z-Axis X/Y Axes -- Alarm -- Trip
Run a measurement cycle to plot statistical RMS velocity trending.

2. Captured Vibration Profile (4,096 Samples @ 8 kHz)

Select or run a measurement to inspect the captured vibration waveform.

Specifications

Parameter Specification
1 Indicators & Alarm Evaluation Red / Amber / Green LEDs • ISO 10816-3, Custom User & Temperature Limits
2 Wireless Connectivity Bluetooth Low Energy 5.2
3 Axes, Sampling & Statistics 3-Axis (X, Y, Z) @ 8 kHz (4,096 samples) • RMS/Peak Velocity, RMS Accel, Temperature
4 On-Board Storage 32 MB Non-Volatile Flash
5 Battery & Operating Temp Li-SOCl₂ Battery (-40°C to +85°C)
6 Enclosure & Sealing Machined Aluminium Base + ABS Cap, Epoxy Potted
7 Mounting Bolted (Center M5 Screw) or Glued (Flat Base)
PLANT-WIDE MOTOR HEALTH

Stop Unplanned Downtime Across Your Entire Motor Fleet

Mount sensors across pump rows, compressor skids, and fan banks without running conduit or network cables. Each unit tracks its machine's health around the clock—warning operators on the shop floor and syncing trend history over Bluetooth LE.

Continuous Per-Motor Health Tracking

Every sensor wakes on schedule, measures 3-axis vibration and casing temperature, checks ISO 10816-3 limits, and saves 32 MB of trend history and raw waveforms on the machine.

At-a-Glance Floor Triage

High-visibility Green, Amber, and Red LED strobes shine through the cap so anyone walking the aisle spots a motor entering Alarm or Trip before it fails.

Walk-By or Gateway BLE Sync

Pull months of velocity trends and 4,096-sample waveforms from dozens of motors and pumps using a tablet on a walk-by route or a fixed Bluetooth LE gateway.

Start Monitoring Your Motors

Protect Your Critical Motors and Pumps from Unexpected Breakdowns

Tell us about the motors, pumps, or rotating equipment you want to track. We will help you size a sensor deployment, set alarm thresholds for your machines, or start a pilot evaluation on your shop floor.

  • • Ready-to-mount wireless sensors for motors, pumps, fans & gearboxes
  • • On-device ISO 10816-3 velocity trending & 4,096-sample waveform capture
  • • Configurable sampling schedules, alarm limits & Bluetooth LE sync

Request a Pilot or Deployment Quote