# Wireless Industrial Vibration & Motor Health Sensor — Complete Technical Reference > Autonomous wireless 3-axis vibration and temperature sensor engineered to prevent unplanned downtime across industrial electric motors, centrifugal pumps, compressor skids, fan banks, and gearboxes. --- ## 1. Executive Summary Unplanned rotating-equipment failures—most commonly rolling-element bearing wear, shaft misalignment, rotor unbalance, cavitation, and mechanical looseness—cause costly production halts. Traditional wired vibration monitoring requires pulling conduit and communication cables across the plant floor, while manual monthly clipboard routes miss rapid bearing degradation between inspections. This wireless industrial vibration sensor bolts or glues directly onto any motor or pump casing in minutes. It wakes on a configurable schedule, samples 3-axis vibration at 8 kHz, computes velocity and acceleration statistics on the device, checks ISO 10816-3 severity zones, flashes high-visibility Green/Amber/Red status LEDs on the machine, and logs both long-term statistical trends and raw 4,096-sample diagnostic waveforms into 32 MB of on-board flash memory for Bluetooth Low Energy 5.2 readout. --- ## 2. Signal Processing & On-Device Diagnostics Pipeline 1. **Scheduled 3-Axis High-Rate Capture**: - Captures 4,096 contiguous 16-bit samples per axis across X, Y, and Z axes at an 8,000 Hz (8 kHz) sampling rate (512 ms capture window per axis, 4 kHz Nyquist bandwidth). - Measures casing temperature concurrently to correlate thermal rise with mechanical wear. 2. **DC Bias Removal & Digital Filtering**: - Computes and subtracts static gravitational DC offset across the 4,096-sample window. - Integrates acceleration to velocity (mm/s) using a digital 5 Hz high-pass filter to eliminate low-frequency drift and integration runaway. 3. **Statistical Feature Extraction**: - **Broadband RMS Velocity (mm/s)** on X, Y, and Z axes (primary metric for ISO 10816-3 machine health evaluation in the 10 Hz to 1,000 Hz band). - **Peak Velocity (mm/s)** on X, Y, and Z axes for impacting and transient detection. - **RMS Acceleration (g)** for high-frequency bearing raceway and gear-mesh fault detection. - **Temperature (°C)** for thermal trending and over-temperature alarm evaluation. 4. **On-Device ISO 10816-3 Zone Evaluation & LED Triage**: - **Zone A/B (Normal — Green LED)**: RMS velocity < 4.2 mm/s. Machine vibration is within healthy continuous operating limits. - **Zone C (Alarm — Amber LED)**: RMS velocity between 4.2 mm/s and 9.5 mm/s. Machine health is degrading; maintenance should be scheduled before failure occurs. - **Zone D (Trip — Red Double-Strobe LED)**: RMS velocity >= 9.5 mm/s. Severe vibration capable of causing immediate bearing or shaft damage. --- ## 3. Mechanical & Environmental Engineering - **Enclosure Construction**: CNC-machined aluminium base for high mechanical stiffness and low acoustic attenuation, paired with a high-visibility frosted pearl-white injection-molded ABS cap. - **Solid Epoxy Potting**: Internal electronics and battery are encapsulated in rigid industrial epoxy potting compound. This provides hermetic protection against washdowns, humidity, oil mist, and corrosive atmospheres while eliminating internal PCB resonance up to the kHz range. - **Mounting Options**: 1. **Bolted Mounting**: Central counterbored through-hole accepts a standard M5 socket head cap screw (DIN 912) for direct threaded attachment into a tapped hole or stud adapter on the motor end-bell or bearing housing. 2. **Adhesive Mounting**: Flat precision-machined aluminium bottom face bonds directly to curved or flat motor frames using industrial cyanoacrylate or two-part epoxy mounting pads. - **Power & Thermal Rating**: Primary Lithium Thionyl Chloride (Li-SOCl2) cell rated for -40°C to +85°C (-40°F to +185°F), delivering multi-year autonomous operation across freezing outdoor pump stations and hot motor housings. --- ## 4. Storage Architecture & Wireless Synchronization - **32 MB Non-Volatile Flash Memory**: - Dedicated circular wear-leveled partitions for compact statistical trend records and full 4,096-sample 3-axis raw waveforms. - When raw waveform pages wrap after long-term disconnected operation, historical statistical trend records remain preserved so long-term degradation curves are never lost. - **Bluetooth Low Energy 5.2 (BLE)**: - Supports both **walk-by collection** (technician with a smartphone or rugged tablet walking the aisle) and **continuous gateway sync** (fixed industrial BLE-to-Ethernet/MQTT/Modbus gateways). --- ## 5. Complete Technical Specifications - **Indicators & Alarm Evaluation**: Red / Amber / Green LEDs • ISO 10816-3, Custom User & Temperature Limits - **Wireless Connectivity**: Bluetooth Low Energy 5.2 - **Axes, Sampling & Statistics**: 3-Axis (X, Y, Z) @ 8 kHz (4,096 samples) • RMS/Peak Velocity, RMS Accel, Temperature - **On-Board Storage**: 32 MB Non-Volatile Flash - **Battery & Operating Temp**: Li-SOCl2 Battery (-40°C to +85°C) - **Enclosure & Sealing**: Machined Aluminium Base + ABS Cap, Epoxy Potted - **Mounting**: Bolted (Center M5 Screw) or Glued (Flat Base) --- ## 6. Frequently Asked Questions (FAQ) ### How does the sensor detect motor and pump failures before breakdown? By waking on schedule to sample 3-axis vibration at 8 kHz (4,096 samples per axis) and integrating acceleration into broadband RMS velocity (mm/s). Rising RMS velocity and high-frequency acceleration harmonics reveal bearing spalling, rotor unbalance, shaft misalignment, and pump cavitation weeks before catastrophic seizure. ### Does installing the sensor require running power or network cables? No. Each sensor is self-powered by an internal -40°C to +85°C Li-SOCl2 battery, stores up to 32 MB of measurements locally on the motor, displays health status via built-in Green/Amber/Red LEDs, and offloads data wirelessly over Bluetooth Low Energy 5.2. ### How is the sensor mounted to an electric motor or centrifugal pump? It can be bolted directly using a single center M5 socket head cap screw passing through the counterbored shaft, or glued to the motor/bearing housing using its flat machined aluminium base and industrial adhesive. ### What happens if no gateway or tablet connects for months? The sensor continues waking on schedule, evaluating ISO 10816-3 alarms, driving its status LEDs on the shop floor, and logging statistical velocity trends and raw waveforms into its 32 MB non-volatile flash memory until a mobile device or gateway connects.